This Car engine heater 5KW is a small and smart car water parking heater. Small size, Low fuel consumption, Low noise, Large flow, Intelligent plateau, APP control, Remote upgrade
This Car engine heater 5KW is a small and smart car water parking heater. Its medium circulation system is connected with the cooling system of an automobile engine. In such a way, the cooling liquid for the engine can be heated by the heater while the engine is not working, so as to increase the temperature of the engine and the interior of the automobile.
With the help of the Car engine heater, it is easy to start the engine even at very low temperatures and both the drivers and passengers can have a warmer environment.
The cooling liquid of the engine flows through the water inlet pipe, the furnace cavity between the furnace inner casing and outer casing, and the water outlet pipe, forming a complete loop for the cooling liquid circulation system. The circulation is forced by the water pump. In this way, the cooling liquid of the engine can be heated again and again in the furnace, and the temperature of the engine, water-tank, heat-exchanger, and cab can rise gradually.
Pls ensure that the Battery used can provide 30A INSTANTANEOUS CURRENT when starting the heater, Recommended 60AH battery at least.
Be sure to read the instruction manual carefully before installation and use.
If the temperature of cooling liquid is higher than 70°C, the heater can only be started after the temperature is reduced through pump circulation.
Power Supply
Heater power leads (positive and negative line) must be connected to the 12V/24V batteries directly. Battery more than 2 years which lack of electric frequently should be changed a new one in order to ensure normal use of the heater.
Fuel Supply
The fuel for the heater can be from the fuel tank in the car or from optional 5L independent fuel tank. The fuel pump is used for transmission of fuel and regulation of supply quantity of fuel.
Fuel pump installation
The optimum installation angle for the fuel pump is from 15 to 35 degrees, the allowable installation angle is from 35 to 90(max) degrees.
Attention for the fuel level, see attached photos.
Max.fuel level – 2
Min.fuel level – 3
Fuel inlet level – 4
Fuel standard
Gasoline should accord with standard DIN EN288
Diesel should accord with standard DIN EN590
Note: Fuel brand which used should meet the requirements of low temperature in winter. Biofuel is forbidden!
Heating medium |
Belief 5KW engine heater |
Battery (60AH recommended) |
INSTANTANEOUS CURRENT 30A |
Thermal power(W) |
5000 |
Power(W) |
1500-5000 |
Fuel type |
Gasoline |
Fuel consumption(l/h) |
0.2 ~ 0.69 |
Rated voltage |
DC12V |
Power consumption(W) |
10 ~ 37 (at starting<100) |
Working pressure(Mpa) |
0.25 |
Lowest working temperature |
-40℃ |
Working height above sea level |
≤5000m |
APP control |
Andriod and Iphone |
Coolant starting temperature |
45℃ |
CTN size (cm) |
47×31×20 |
Express(UPS/Fedex) Weight (kg) |
8 |
Our factory was established in April 1998, located in Harbin, Heilongjiang province. We have an independent R&D organization and has established long-term cooperative relationships with state key universities and colleges like Harbin Institute of Technology, Harbin Engineering University, etc. Annual production is more than 150,000 sets. We exported to Europe, the United States, Canada, Japan, and etc 60 countries. We have sole dealers in AU and UK and Denmark.
No. | Name | Specifications | Amount |
1 | Parking heater | 5KW | 1 |
2 | Timer | 1 | |
3 | Fuel pump | YB-Ⅰ-12V(24V) | 1 |
4 | Muffler | XYQ-Ⅰ | 1 |
5 | Wiring harness | 1 | |
6 | Water pump | 12V (24V) | 1 |
7 | Heater bracket | 1 | |
8 | Rubber cushion | 4 | |
9 | Muffler bracket | 1 | |
10 | Air inlet pipe | Φ20.5/Φ24 L=900 | 1 |
11 | Exhaust pipe | Φ24/Φ29.5 L=1000 | 1 |
12 | Positive wire of power supply | 1 | |
13 | Fuse base | With cover | 1 |
14 | Fuse | QY169-5A | 1 |
15 | Fuse | 12V/20A(24V/15A) | 1 |
16 | Fuse | QY169-25A | 1 |
17 | Water pipe | Φ17/Φ27 L=2600 | 1 |
18 | Clip | 16-25 | 1 |
19 | Spring clip | Φ24×Φ27 | 10 |
20 | Oil pump clip | Φ32 | 1 |
21 | Oil pipe clip | 8-10 (9-11) | 12 |
22 | Exhaust pipe clip | Φ24-28 | 3 |
23 | Air inlet pipe fixing clip | Φ24 t=0.5 | 2 |
24 | Exhaust pipe fixing clip | Φ27 t=0.8 | 2 |
25 | Fuel pipe | GasolineΦ1.5×Φ4(DieselΦ2×Φ5) | 1 |
26 | Fuel pipe connector | Φ3.5/Φ9.5(Φ4.1/Φ10.5) | 6 |
27 | water pipe connector | Φ18 L=55 | 2 |
28 | Special water pipe connector | PPA +33 Φ20×Φ18 L=60 | 2 |
29 | Relay | 4141(only for 12V) | 1 |
30 | Filter | RYL-Ⅰ(only for diesel) | 1 |
31 | Bolt | M6×10 | 1 |
32 | Self drilling tapping screw | ST5.5×25 | 6 |
33 | Self drilling tapping screw | ST5.5×30 | 5 |
34 | Self tapping screw | ST3×20 | 1 |
35 | Self tapping screw | ST4×16 | 3 |
36 | Spring washer | Φ6 | 2 |
37 | Washer | Φ6/Φ12 | 2 |
38 | Nut | M6 | 1 |
39 | Fuel suction pipe | XYG-Ⅰ 3×400 | 1 |
40 | Plug | DJ7041A-2.8-21 | 1 |
41 | Nylon cable ties | 4×150 | 1 |
42 | Nylon cable ties | 4×200 | 1 |
43 | Instruction manual | 1 | |
44 | Reducing T | Φ6-Φ10/Φ10 | 1 |
45 | Oil pipe clip | 12-14 | 2 |
46 | Non-return valve | D18 | 1 |
47 | Transition elbow | 2 | |
48 | Fixing gear | 2 | |
49 | O-ring | 14.8×2.62 | 2 |
50 | Bolt | M6×95 | 4 |